Bosch Dishwasher Error Codes
Find your code in the list below. Each page explains what the code means, the most likely causes, step-by-step fixes you can do yourself, and the parts that commonly resolve it. 34 codes covered.
Shop Bosch Dishwasher parts at RepairClinic
- E01 — There is a heat pump motor circuit fault at the main control board. On current models Bosch treats this as an electronics fault, not a…
- E0100 — Four-digit display form of E01 on newer models: a heat pump motor circuit fault at the main control board.
- E02 — There is a main control board relay fault. Bosch lists E02 and E03 with the same relay-fault meaning on current models.
- E03 — There is a main control board relay fault. On current Bosch models E03 is listed with the same meaning as E02; on much older models E01-E05…
- E04 — The dishwasher detected faulty heater electronics during its self-test. Bosch directs owners to customer support for this code rather than…
- E05 — There is a wash arm diverter circuit fault at the main control board - the part that directs water between spray arms is not being driven…
- E06 — There is a door sensor circuit fault - the dishwasher cannot reliably tell whether the door is closed and latched. On older models this was…
- E07 — The Zeolite (Crystal Dry) fan motor is defective on models with Crystal Dry. On older non-Zeolite models E07 was listed as a dryer fan…
- E08 — On older Bosch models, water is not filling above the level of the heating element - the heat pump detects the water level in the cabinet…
- E09 — There is a heat pump internal heater fault - the water is not being heated properly. Older Bosch lists described E09 as a general water…
- E10 — There is a Zeolite (Crystal Dry) chamber heater fault on models with Crystal Dry. Older Bosch lists described E10 as a heating element…
- E11 — On older Bosch models, the thermostat or temperature sensor (NTC thermistor) is faulty, so the dishwasher cannot read water temperature…
- E12 — There is limescale build-up in the heat pump and the dishwasher needs descaling. This is a maintenance code, especially common in…
- E13 — On older Bosch models, the incoming water temperature is too high - over about 75C / 167F. This code is not on Bosch's current US list.
- E14 — There is a flow meter failure, or a problem with water flowing into the dishwasher or the filling system. Older lists called this a reed…
- E15 — The safety switch has detected water in the base of the dishwasher and the leakage protection (AquaStop) system has activated. The machine…
- E16 — There is a problem with water flowing into the dishwasher or the filling system - water may not be able to enter. Bosch lists E16 and E17…
- E17 — There is a problem with water flowing into the dishwasher or the filling system - water may not be able to enter correctly. Bosch lists E16…
- E18 — There is a problem with water flow into the dishwasher: the water level is too low, or water is not being pumped correctly. Older lists…
- E19 — On current models Bosch lists E19 as a detergent dispenser solenoid circuit fault. On some older and European models the same code was used…
- E20 — On current models Bosch lists E20 as a heat pump internal heater fault. On older models E20 meant a circulation pump winding resistance…
- E21 — The heat pump (circulation pump) is blocked on current models. Older lists also described E21 as a circulation pump blockage, often debris…
- E22 — The dishwasher filter is blocked with food particles and needs cleaning. This is routine maintenance, not a breakdown.
- E23 — There is a problem with the drain pump - it is blocked, clogged or faulty. Older lists specified a drain pump winding resistance…
- E24 — The dishwasher is not draining properly, which Bosch attributes first to a blocked drain filter. A kinked drain hose or a blocked disposal…
- E25 — The drain pump is blocked, or the drain pump cover is loose or missing. This is the classic homeowner-fixable Bosch drain code.
- E26 — On older Bosch models, there is a water switch or regulator problem - the part that directs or regulates water flow is faulty. This code is…
- E27 — The house power supply to the dishwasher is too low. This is an incoming voltage problem, not a fault inside the dishwasher.
- E28 — On older Bosch models, a fault was detected with the turbidity (aqua) sensor, which measures how dirty the water is to set the cycle. This…
- E3100 — Four-digit display form of E15 on newer models: the safety switch has detected water in the base and leakage protection has activated.
- E6102 — Four-digit display form of E25 on newer models: the drain pump is blocked, or the drain pump cover is loose or missing.
- E6103 — Four-digit display form of E24 on newer models: the dishwasher is not draining properly due to a blocked drain filter.
- E9001 — Four-digit display form of E27 on newer models: the house power supply to the dishwasher is too low.
- H01 — This is not an error code. H01 (shown as h:01, with h:02, h:03 and so on for longer times) means a delay-start timer has been set - the…