GE Washer Error Codes
Find your code in the list below. Each page explains what the code means, the most likely causes, step-by-step fixes you can do yourself, and the parts that commonly resolve it. 40 codes covered.
Shop GE Washer parts at RepairClinic
- 7E — Water supply error on GE WSL model washers (PartSelect): the washer has a problem with its water supply / fill sensing.
- dE — Lid open on GE electronic-control top-load washers: the control sees the lid as open, so the cycle stopped or will not start. On GE WSL…
- E22 — Fill timeout on GE front-load washers: the washer did not fill, or filled too slowly, and timed out (about 8 minutes).
- E23 — Flood-protect / overfill fault on GE front-load washers: the washer detected too much water, or the foam/level switch closed while the…
- E30 — No drain on GE front-load washers: the control does not detect the drain pump running or the washer cannot drain at all.
- E31 — Drain timeout on GE front-load washers: the washer is draining, but too slowly, and timed out.
- E38 — Dispenser error on GE front-load washers: the detergent dispenser cannot move into its selected position - you may hear it repeatedly…
- E39 — Dispenser timeout on GE front-load washers: the dispenser does not move, or its switches do not open and close as expected.
- E42 — Drive motor instantaneous / excess current on GE front-load washers: the motor drew too much current, most often because the load is too…
- E43 — Inverter DC fault on GE front-load washers: the main control detects a defect in the inverter control board that manages drive motor speed.
- E45 — Drive motor overload current on GE front-load washers: the motor overloaded, usually because the load is too heavy.
- E46 — Drive motor / inverter over-temperature on GE front-load washers: the drive motor overheated during operation.
- E47 — Heat sink / inverter over-temperature on GE front-load washers: the inverter control board's heat sink overheated.
- E48 — Open motor phase on GE front-load washers: one phase/winding of the drive motor is open, so the motor cannot run correctly.
- E49 — Drive motor overload power on GE front-load washers: the motor is overloaded beyond its power limit.
- E4A — Inverter under-voltage on GE front-load washers: the DC bus voltage in the inverter is too low.
- E4B — Inverter power-up fault on GE front-load washers: a software/hardware problem occurred when the inverter powered up.
- E4C — Inverter over-voltage on GE front-load washers: the DC bus voltage in the inverter is too high.
- E4E — Inverter under-voltage after start on GE front-load washers: the minimum voltage was not received after starting, so the motor does not run.
- E52 — Main control wake-up error on GE front-load washers: communication was lost between the main control and the drive motor control.
- E53 — Buffer error on GE front-load washers: an internal software buffer error occurred in the control.
- E54 — No motor response on GE front-load washers: communication was lost between the main control and the drive motor, and the motor does not…
- E57 — Checksum failure on GE front-load washers: a main control board software error occurred - Sears PartsDirect lists E57/E58 as main control…
- E58 — Communication failure on GE front-load washers: a non-recoverable communication error - listed as main control board failure.
- E60 — Door lock switch failure on GE front-load washers: the door lock switch failed while locking.
- E61 — Door unlock switch failure on GE front-load washers: the door unlock switch in the lock assembly failed.
- E62 — System contact failure on GE front-load washers: a system contact fault involving the heater, pump, pressure switch or door lock circuit.
- E63 — Unexpected open door on GE front-load washers: the control detected the door as open when it should be locked - grouped with the door lock…
- E64 — Unexpected open door while running on GE front-load washers: the door was detected open during operation.
- E65 — Water level sensor failure on GE front-load washers: the pressure/water level sensor is not reading correctly.
- E66 — Water temperature sensor fault on GE front-load washers: the temperature sensor is defective - listed as open in the GE service table.
- E67 — Water temperature sensor shorted on GE front-load washers: the temperature sensor circuit is shorted.
- E70 — Stuck key on GE front-load washers: a control panel key was read continuously for about 60 seconds.
- E71 — Key fault / defective main control board on GE front-load washers: a communication error between the control and the keys, listed as a…
- FE — GE Consumer Help Indicator: water has reached a critical level in the washer. GE's instruction is to turn off water and power to the washer…
- H2O SUPPLY — GE's Consumer Help Indicator message that water is not entering the washer / the washer cannot sense the water level. GE says on front-load…
- IE — Water level sensor error on GE WSL model washers (PartSelect). Note the same letters are used on newer GE washers as a Consumer Help…
- LId — Top-load display message that the cycle stopped because the lid is open; GE also shows 'Lid' when 3 cycles have been started without…
- OE — Water overflow error on GE WSL model washers (PartSelect): the washer detected an overflow condition.
- UE — Unbalanced load on GE electronic-control washers: the laundry load is unbalanced, so the washer cannot spin up properly.