Samsung Washer Error Codes
Find your code in the list below. Each page explains what the code means, the most likely causes, step-by-step fixes you can do yourself, and the parts that commonly resolve it. 68 codes covered.
Shop Samsung Washer parts at RepairClinic
- 1C — Water level sensor issue, grouped by Samsung with the water level / leakage errors. Moisture may be detected where it does not belong, or…
- 1E — Water level sensor fault. Samsung lists causes including incorrect sensor terminal connections and a folded or clogged sensor hose.
- 3C — Motor error: check the drum motor for operation. Samsung lists 3C in its motor-error group.
- 3CP — Electronic control issue related to the motor control. Samsung UK lists 3CP as an electronic control issue; restart the cycle first.
- 3E — Motor error on most models (on some models 3E is instead a voltage error - check the model manual). Samsung groups 3E with 3C motor errors…
- 4C — Water is not supplied to the washer, or it is not filling correctly. This is the newer display form of the older 4E and nF not-filling…
- 4C2 — The water from the cold supply is extremely hot, usually because the hot and cold hoses are swapped. This is the newer form of the 4E2…
- 4E — Water is not supplied to the washer, or it is not filling correctly. This is the older display form of the newer 4C code (also shown as nF…
- 4E1 — Water temperature issue: incoming water is too hot, or the hose is connected to a hot supply instead of cold. Samsung groups 4E1 with 4C2…
- 4E2 — The water from the cold supply is extremely hot, usually because the hot and cold hoses are swapped. This is an older form of the newer 4C2…
- 5C — Water is not draining from the washer, or is draining too slowly. This is the newer display form of the older 5E and nd no-drain codes.
- 5E — Water is not draining from the washer, or is draining too slowly. This is the older display form of the newer 5C code (also shown as nd or…
- 8C — MEMS sensor issue: the vibration / MEMS sensor is reporting a problem. Turn the appliance off and restart the cycle first.
- 8E — MEMS / vibration sensor error group (Samsung US lists 8E, 8E1 and 8E2 with the MEMS sensor errors; Samsung UK describes 8E as a current…
- 9C1 — Voltage error: there is an irregularity / low voltage in the electrical supply to the washer. Samsung groups 9C1 with 9C2 voltage errors.
- 9C2 — Low voltage / voltage error variant of 9C1. Samsung UK lists 9C1 and 9C2 together as low voltage - check power is supplied properly and the…
- 9E1 — Power error. Samsung UK groups 9E1 and 9E2 as power errors and Samsung US lists 9E1 in its voltage-error group.
- AC — Communication error: check communications between the main and sub PBAs. Samsung groups AC with AE signal communication errors.
- AC6 — Signal / inverter communication issue: communications between the main and inverter boards have failed. Samsung lists AC6 with AC…
- AE — Communication error, an older display form related to AC. Samsung groups AE with AC electronic control / invalid communication errors.
- bE2 — Jammed button error: a button on the panel is detected as stuck or continuously pressed. Samsung lists bE2 with E2, 6E2 and BE2…
- CE — Hot/cold error: the cold water supply is extremely hot, which Samsung lists with 4C2 and 4E2 and says usually means the supply hoses are…
- dC — The washer is operating, or trying to operate, with the door not detected as closed and locked. Note: on some models dC instead signals an…
- DC1 — Door issue / main door lock or unlock is not working properly. Samsung groups DC1 with dC and dE door errors.
- DC3 — Add Door lock issue. Samsung lists DC3 (also dC3) with the Add Door errors.
- ddC — The Add Door was opened without pressing Start/Pause first, or is not detected as closed. Samsung also shows this as DDC.
- dE — Door error: the door is not detected as closed and locked. Samsung groups dE with dC door errors (older display form).
- dL — Door error: the door is not detected as closed and locked. Samsung lists dL in its door-error group with dE, dC and dS.
- dS — Door error: the door is not detected as closed and locked. Samsung lists dS in its door-error group with dE, dC and dL.
- E1 — Water supply issue: the washer is not detecting that it is filling with water. Samsung groups E1 with the 4C and 4E water-supply codes.
- E2 — Water drainage issue: water is not draining from the appliance. Samsung lists E2 as the old code paired with 5E / 5C.
- E4 — The load in the drum is unbalanced. Samsung lists E4 as an old code for the UE / Ub unbalanced-load error.
- E7 — Water level sensor issue. Samsung lists E7 as an old code paired with 1E / 1C.
- E9 — Low water level detected. Samsung lists E9 as an old code paired with LE / 11E leakage errors.
- FL — Door lock error: the door is unable to lock properly. Samsung lists FL in its door / door-lock error groups with LO and dE.
- HC — High temperature heating check / heater error. Samsung lists HC with HE and HE1 heater errors.
- HE — Heater error, an older display form related to HC. Samsung groups HE with HC and HE1 heater errors.
- HE1 — Water heater not functioning. Samsung UK says to contact the Samsung Service Centre for HE1.
- HOT — The appliance is too hot. Samsung says this is not a fault: the fan runs until the washer cools to about 55C, then the door unlocks.
- Hr — Heater error variant: Samsung lists Hr with HC, HE and HE1 in its heater-error group (Hr is a heater relay fault on many models).
- LC — Low water level detected / water leakage error: moisture is detected somewhere it does not belong, or water is leaving the tub. When LC…
- LC1 — Low water level / leakage error, a variant of LC. Samsung groups LC1 with LC, LE and LE1.
- LE — Water leak / low water level detected during the cycle - a natural drain or leak error. This is the older display form related to the newer…
- LE1 — Water leak / low water level variant of LE. Samsung groups LE1 with LE, LC and LC1.
- LO — Door lock error: the door is unable to lock properly. Samsung lists LO with L0, dE and FL as door-lock errors.
- nd — No-drain error: water is not draining at the correct speed, or at all. This is an older display form of the newer 5C / older 5E drain code.
- nF — The washer has tried to fill but was unsuccessful - a 'no fill' error. This is an older display form of the newer 4C / older 4E…
- nF1 — Hot/cold error: the cold water supply is extremely hot because the hoses are swapped. Samsung lists nF1 with 4C2, 4E2 and CE.
- OC — Overflow error: there is too much water in the washer. This is the newer form of the older OE overflow code.
- OE — Overflow error: there is too much water in the washer. This is an older display form of the newer OC code (also shown as OF on some models).
- OF — Overflow error: the washer thinks there is too much water in the machine. Samsung groups OF with OC and OE overflow errors.
- PC — Clutch position error: the position of the clutch can't be detected. Samsung groups PC with PE clutch position errors.
- PC1 — Clutch hall signal error: the clutch position was detected but its hall signal is malfunctioning. Samsung groups PC1 with PE1.
- PE — Clutch position error, an older display form paired with PC. Samsung lists PC and PE together.
- PF — Power failure / voltage error: power went out, the washer was unplugged, or the breaker tripped before the washer powered itself off.…
- SC — No-drain error: water is not draining at the correct speed, or at all. Samsung lists SC in the same group as 5C, 5E, SE and nd.
- Sd — Excessive suds error, a display variant of SUd (also shown as 5d). The washer stops briefly to allow suds to dissipate.
- SDC — Detergent drawer error: the detergent drawer is not completely closed. Samsung lists SDC and 5DC for this; the drawer clicks when fully…
- SE — No-drain error: water is not draining at the correct speed, or at all. Samsung lists SE in the same group as 5C, 5E, SC and nd (the 5 can…
- SUd — Excessive suds detected. The washer pauses to let suds dissipate and then continues automatically; Samsung says this does not indicate…
- tC — Temperature sensor error. Samsung lists tC with tE and tE1 temperature sensor errors.
- tE — Temperature sensor error. Samsung lists tE with tE1 and tC temperature sensor errors.
- tE1 — Temperature sensor error, a variant in Samsung's tE / tC group (tE1, tE2 and tE3 are also listed by Samsung UK).
- U6 — Unbalanced load error, a variant in Samsung's Ub / UE group. The washer will fail to complete the cycle because the load is unbalanced.
- Ub — Spinning does not work because the load is unbalanced. This is the newer form of the older UE code; Samsung says this is not a fault with…
- UC — Fluctuation in the supply voltage detected. Samsung says to check the cord is plugged in properly and that the washer is not on an…
- UE — Unbalanced error: the load in the drum is unbalanced and the washer has stopped the spin for safety. This is the older form of the newer Ub…
- Ur — Unbalanced load retry: the washer is adding water and trying to rebalance the load before spinning again. Samsung says Ur itself does not…